Wood Logs Crusher-manufacture,factory,supplier from China

The demand for wood veneer dryer is increasing year by year,and it has been recognized and purchased by consumers.Traditional natural air-dried wood is prone to problems such as deformation and cracking.The use of wood dryer equipment can effectively solve this problem.The cost of dryer equipment is high, so basic maintenance needs to be done in the later use process,such as the ground,ventilation system, gate,instrument,heating system and debugging system,etc.The specific operations are as follows:1.The floor of the wood dryer equipment should be kept clean and tidy,and the debris should be c

Wood veneer is required to be dried in the veneer dryer to remove the moisture content present in it. Moisture content in wood veneer can cause several problems such as warping, cracking, splitting, and decay of the wood, which can lead to a reduction in the quality and value of the veneer.During the veneer manufacturing process, the logs are first peeled into veneer sheets using a lathe or a slicer. These veneer sheets are then sorted, graded, and stacked for drying.

Recently, our new customer successfully installed and put into use the 2 deck veneer dryer provided by our company. During normal operation, the veneer dryer has successfully completed the efficient drying of rubber wood veneers. Normal drying of rubber wood veneers can be dried to zero water, and the drying effect is satisfactory. It not only greatly improves the production efficiency of veneer processing, but also shows great advantages in environmental protection and energy saving.

The hardness of wood is mainly affected by factors such as wood species, density and moisture content. However, the following treatment methods can increase the hardness of wood:Heat treatment: Heat treatment is a method of changing the physical and chemical properties of wood by heating it. This treatment method can increase the hardness, stability and durability of wood.Compression treatment: Compression treatment is a method of compressing wood to a higher density.

Pine is considered one of the most difficult woods to dry, mainly due to its wood structure and composition.1. Uneven density: Pine fibers are relatively fine and soft, resulting in uneven density inside the wood. This makes the wood dry at an inconsistent rate, prone to cracking and warping.2. High moisture content: Compared with other woods, pine has a higher moisture content. It takes longer for the moisture inside the wood to evaporate completely.

Pine is considered one of the most difficult woods to dry, mainly due to its wood structure and composition.1. Uneven density: Pine fibers are relatively fine and soft, resulting in uneven density inside the wood. This makes the wood dry at an inconsistent rate, prone to cracking and warping.2. High moisture content: Compared with other woods, pine has a higher moisture content. It takes longer for the moisture inside the wood to evaporate completely.

1, prevent wood deterioration and decay, extend the life of wood products.Wet wood stacked in the outdoor air for a long time, if no corresponding treatment measures are taken, it is easy to cause rot and insect pests. Reducing the moisture content of wood to less than 20% can greatly reduce the damage to microorganisms and pests. Therefore, usually in the production and processing sector, the wood is dried to a moisture content of about 8-15%.

1, prevent wood deterioration and decay, extend the life of wood products.Wet wood stacked in the outdoor air for a long time, if no corresponding treatment measures are taken, it is easy to cause rot and insect pests. Reducing the moisture content of wood to less than 20% can greatly reduce the damage to microorganisms and pests. Therefore, usually in the production and processing sector, the wood is dried to a moisture content of about 8-15%.

In 2023, Vietnam exported wood chips to 13 markets. China, Japan, and South Korea were the country's three major markets for wood chip exports. In 2023, Vietnam exported over 9.38 million tons of wood chips to the Chinese market, with a value exceeding $1.43 billion, accounting for 65.1% of the export volume and 64.7% of the export value.

The wood veneer dryer needs to pay attention to some problems when drying wood. Before use, it should start the heating fan and start the speed regulating motor when reaching the drying temperature. The veneer should be entered longitudinally from the feed port, the feed should be straightened, the veneer and the drive roller into a 90 degree feed connection, before drying the veneer should be cut neatly. Drying should master the moisture content, according to the moisture content of the board, adjust the speed of the motor.Precautions for operation of wood veneer dryer1.